PARTS PRICE LIST
Call for latest pricing 12-2023
———————————————————-
PRICING EFFECTIVE SEPT. 1, 2015 old list
CLICK HERE for order form.
| PART NO. | DESCRIPTION | PRICE |
| 02-00-06 | Crankshaft, forged | 720.00 |
| 02-00-10 | #3 main bearing, std. | 20.00 |
| 02-00-14 | Step woodruff key | 4.25 |
| 02-00-17 | Thrust spacer (3) shim | 4.50 |
| 02-00-25 | Gear, crank timing | 38.00 |
| 02-00-26 | Nut, gear retainer | 21.00 |
| 02-00-27 | Nut, set screw | .20 |
| 02-00-28 | Dowel, crank (2) | 1.20 |
| 03-00-00 | Con rod (4) 137mm | 230.00 |
| 03-00-00-A | Con rod (4) 139.7mm | 230.00 |
| 03-00-00-B | Con rod (4) 142.24mm 2″ jrnl w/9mm bolts | 250.00 |
| 03-00-05 | Set con rod bearings | 19.00 |
| 04-00-00 | Crankcase | 1360.00 |
| 04-00-06 | Main bearing alignment pin (6) | .90 |
| 04-00-07 | Case stud seals (6) | 1.20 |
| 04-00-10 | Main bearings #1 & #2 | 75.00 |
| 04-01-00 | Cam bearing set | 18.00 |
| 04-01-05 | Cam followers (8) | 75.00 |
| 04-01-12-B | Camshaft 274 degrees (390 lift) w/gear | 140.00 |
| 04-02-01 | Rear crank seal | 6.00 |
| 04-02-02 | Camshaft plug | 1.25 |
| 04-02-04 | Crank flange key | 1.75 |
| 04-02-05-AS | #4 main bearing assembly | 280.00 |
| 04-02-05 | #4 main bearing only | 250.00 |
| 04-02-06 | 1/8″ pipe plug | .60 |
| 04-02-09 | #4 main int. rotary seals (2) | 10.40 |
| 04-02-10 | #4 main outer seal | 10.50 |
| 04-02-11 | #4 main seal snap ring | 2.25 |
| 17-02-04 | Tube fitting, #4 main | 2.15 |
| 04-05-00 | Case stud washers (6) | 1.80 |
| 04-05-01 | Lock nuts, main case (6) | 4.20 |
| 04-05-05 | Secondary case washers (28) | 5.60 |
| 04-05-06 | Secondary lock nuts 8mm (20) | 14.40 |
| 04-05-07 | Top case bolt (long) | .55 |
| 04-05-08 | Top case bolt (short) | .55 |
| 04-05-09 | Bottom case bolts (2) | 1.60 |
| 04-06-02 | Plug seal | 1.20 |
| 04-06-03 | Threaded plug | 5.00 |
| 05-00-00 | Crankshaft flange removal tool | 32.00 |
| 05-00-00-2 | Crankshaft flange | 305.00 |
| 05-00-01 | Flange washer | .75 |
| 05-00-02 | Flange bolt LH (forged shaft) | 58.00 |
| 05-00-05 | Bolt plug | .75 |
| 05-00-06 | Flange moisture seal | 2.25 |
| 06-00-01 | Dipstick | 8.00 |
| 06-00-04 | Set piston rings 92mm 1.5mm | 60.00 |
| 06-00-05 | Set piston rings 82mm 2.mm | Call |
| 06-01-00-2 | 92mm cylinders/pistons set CIMA | 335.00 |
| 06-01-00-4 | 94mm cylinders/pistons set CIMA | 335.00 |
| 06-01-09 | Cylinder stud kit (16) | 64.00 |
| 07-00-05 | Cyl heads, pair complete 94 bore, dual plug | 995.00 |
| 07-00-06 | Cyl heads, pair complete 75HP 92 bore, dual plug | 995.00 |
| 07-00-07-B | Spark plug covers (4) cast | 42.00 |
| 07-01-05 | Intake valves, 40mm SS (4) | 48.00 |
| 07-01-06 | Exhaust valves, 32mm SS (4) | 48.00 |
| 07-01-07 | Valve springs (8) | 24.00 |
| 07-01-08 | Spring ret. (8) | 10.00 |
| 07-01-09 | Split cotters (16) | 8.80 |
| Valve seats installed | (8) $45.00 ea. | 360.00 |
| 08-01-00 | Push rod tubes (8) | 20.00 |
| 08-01-01 | Tube seals (16) | 4.50 |
| 08-01-02 | Cyl head washers (16) | 4.50 |
| 08-01-03 | Cyl head nuts (16) | 6.65 |
| 08-02-00 | Push rods, steel (8) | 38.00 |
| 08-02-01 | Push rods, alum (8) | 45.00 |
| 08-03-00 | Rocker arm assembly (2) | 96.00 |
| 09-01-00 | Sump gasket (2) | 1.80 |
| 09-01-01 | Oil strainer | 4.75 |
| 09-01-11 | Oil sump side drain assembly | 85.00 |
| 09-01-14 | Washers (6) | 3.60 |
| 09-01-15 | Cap nuts (6) | 3.60 |
| 10-01-00 | Copper mesh oil separator | 1.45 |
| 10-01-01 | Gasket, breather | .25 |
| 10-01-02-A | Breather plate | 24.00 |
| 10-01-03 | Breather ret. bolts (4) | .85 |
| 10-01-05 | Breather fitting | .65 |
| 10-01-06 | Breather hose | 2.25 |
| 10-01-08 | 3/8″ plug, oil block-off (2) | 2.00 |
| 10-01-10 | Fuel pump gasket | .50 |
| 10-01-11 | Fuel pump cover plate | 8.55 |
| 10-01-15 | Oil fill cap | 18.00 |
| 10-01-16 | Oil fill cap O ring | .35 |
| 10-01-20 | L/L front block-off plate | 10.00 |
| 10-01-22 | L/L front gasket | .35 |
| 11-00-00-AS | Shipping legs (4) exhaust pipes | 80.00 |
| 11-01-02-A | Starter flywheel for magneto | 265.00 |
| 11-01-02-B | Starter flywheel for CDI | 325.00 |
| Flywheel bolt socket | 9.50 | |
| Ring gear (only) | 72.00 | |
| 11-01-06 | Alternator rotor | 170.00 |
| 11-02-07 | Rotor ret. screws (6) | 3.60 |
| 11-01-08 | Rotor lock washer (6) | .90 |
| 1-01-09-A | Mag cplg. (non-starter engine) | 45.00 |
| 11-01-11-A | Flywheel dowel pin (2) | 2.00 |
| 1-01-13-B | Flywheel ret. screws (4) | 20.00 |
| 1-01-14-A | Alternator stator (20 amp) | 160.00 |
| 11-01-16 | Stator ret. screws (4) | 1.20 |
| 11-01-17 | Stator lock washer (4) | .48 |
| 11-01-30 | Voltage regulator/rectifier | 65.00 |
| 11-02-00 | Mag mount housing (for Bendix) | 185.00 |
| 11-02-04 | Housing bolt, 55mm (2) | 3.30 |
| 3.30 | Housing bolt, 60mm (2) | 3.30 |
| 11-02-06 | Housing bolt washer (4) | 1.00 |
| 11-02-08 | Housing bolt lock nuts (2) | 2.20 |
| 11-03-01 | Starter bolts (2) | 2.60 |
| 11-03-03 | Starter bolt washers (2) | .60 |
| 12-00-12 | Mag drive rubber vib. (2) | 12.00 |
| 12-00-13 | Mag drive ret. cup | 15.00 |
| 13-01-00 | Spark plugs NGK3932 | 3.65 |
| Spark plug socket machined to 1 | 12.50 | |
| 14-00-00 | Slick single ignition magneto | Call |
| 14-00-05 | Mag hold down clamp (2) | 10.20 |
| 14-00-15 | Ground terminal assembly, P-lead kit (2) | Call |
| 14-01-00 | Rocker arm covers, complete | 60.00 |
| 14-01-01 | Rocker arm cover gasket (2) | 5.00 |
| 14-01-02 | Rocker arm cover bolts (4) | 2.00 |
| 14-01-03 | Rocker arm cover washers (4) | 2.40 |
| 15-00-00 | Lower intake manifold | 65.00 |
| 15-00-01 | Intake manifold, left | 125.00 |
| 15-00-02 | Intake manifold, right | 125.00 |
| 15-00-03 | Intake manifold gaskets (2) | 3.00 |
| 15-00-06 | Intake manifold coupling hose (3) | 30.00 |
| 15-00-07 | Coupling hose clamp | 5.00 |
| 15-00-10 | Set intake manifold | 345.00 |
| 15-02-05 | Injector coupling hose | 10.00 |
| 15-02-10 | RevFlow flange adapter | Call |
| 15-02-11 | Air filter | 45.00 |
| 15-02-15 | Alternate air source/ram air filter assembly | 130.00 |
| 15-04-02 | RevFlow carburetor 30 – 36mm | 385.00 |
| RevFlow carburetor 38 – 40mm | 405.00 | |
| 16-00-00 | Oil pump, single function internal outlet 38mm gears | 95.00 |
| 16-00-00-T | Oil pump, dual body for turbo | 265.00 |
| 16-00-01 | Oil pump with oil filter mount, oil bypass 38mm gears | 365.00 |
| 16-00-05-B | Pump cover, oil bypass with filter mount, without pump | 185.00 |
| 16-01-00-AS | Oil cooler assembly with bracket, lines | 285.00 |
| 16-01-05 | Oil line, case to cooler | 65.00 |
| 16-01-06 | Oil line, filter to cooler | 65.00 |
| 16-01-11 | AN8 fitting eng case 18 X 1.50m | 13.50 |
| 16-01-12 | Oil cooler, bare | 135.00 |
| 16-01-15 | Fuel pump/oil pump assembly (outright) 38mm gears | 390.00 |
| 16-06-06-D | Geared starter for 109T ring gear | 225.00 |
| 16-06-06-E | Hi-torque starter for 12v ring gear | 295.00 |
| 19-00-00 | Vacuum pump bracket, pulley, bolt | 175.00 |
| 20-00-15 | Engine mount sleeves (4) | 8.00 |
| 20-00-16 | Engine mount conical bushings set (8) | 38.00 |
| 20-00-17 | Wide area washers (4) | 4.00 |
| 20-00-20 | Engine mount hardware kit, complete | 75.00 |
| 20-00-30 | Sonex engine mount hardware kit (special) | 100.00 |
| 26-00-51 | Prop crush plate | 40.00 |
| 26-00-54 | Prop extension 3 | 365.00 |
| Prop extension 4 | 375.00 | |
| Q-2 or KR exhaust system, mild steel | 350.00 | |
| Q-2 or KR exhaust system, stainless steel | 510.00 |